By: New York Times |

Updated: April 3, 2020 10:29:39 am

By Tracy Ma and Natalie Shutler

Guidance on whether to wear a face mask has been evolving. The Centers for Disease Control and Prevention currently advises against healthy people wearing masks but is reviewing its guidance, particularly in light of a new belief that as many as 25 per cent of people infected with the new coronavirus may not show symptoms.

It is still most important to limit trips outside and wash your hands frequently. Civilians should not use medical-grade masks, which are in short supply and must be reserved for health care workers on the front line.

But those who are sick with the new coronavirus can help limit the spread of respiratory droplets by wearing a mask, and that applies to those who are asymptomatic or undiagnosed as well. Plus, some organizations are using fabric masks as a temporary stopgap. The Sewing and Craft Alliance is continuously updating a list of health care facilities that have asked for fabric mask donations.

You will need:

— Needle and thread (and a sewing machine, if you have one)

— Scissors

— Pins or clips to hold fabrics in place (safety pins and paper clips will also work in a pinch)

— At least 20 inches by 20 inches of 100% cotton fabric, such as a flat tea towel

— 4 strips of cotton fabric for ties, about 18 inches long and 3/4-inch wide

— Two flat (1/4 inch) sewing elastics that are 7 inches long each

Step 1: Prepare your materials

Choose your piece of cotton fabric, prewash it on the warmest setting and dry it on high heat. (Tea towels are better to use than T-shirts or linens, according to the Stanford Anesthesia Informatics and Media Lab.)

Fold the fabric in half. Measure and cut out a 9 1/2 inch by 6 1/2 inch rectangle to create two identically sized layers. This is your mask base.

Now it’s on to the fabric ties.

Cut 4 thin pieces of material, about 18 inches long and 3/4 inch wide. Fold each piece of fabric twice lengthwise, then once more to tuck the rough edges inside. Sew a straight line along the middle. This will prevent the fabric ties from having frayed edges.

Step 2: Adding the ties

Take one of your rectangular fabric layers. With the “right side” (or the outer-facing side, where the pattern might be) facing you, pin down the 4 fabric ties, one piece per corner. Make sure that the ties are gathered in the center of the fabric layer before advancing to the next step.

You can also substitute sewing elastic for fabric ties, but note that elastic cannot be bleached (and therefore, is not as easy to clean) and that anyone with a latex allergy cannot wear it. (Elastic is also increasingly in short supply.) Attach elastics to the first layer of fabric by securing the ends at the corners, forming little hoops. Make sure the elastic lies inside the perimeter of your fabric.

Step 3: Putting it together

Take the second layer of fabric and line it up with the first. The “right sides” (or patterned sides) of the fabric should be facing each other, sandwiching the fabric ties or elastics. Secure the fabric sandwich together with pins.

Step 4: Start stitching

Eyeball a midway point. From the middle, sew a straight line across the mask, about 1/4-inch above the bottom edge of the fabric, toward the bottom left-hand corner. Remove any pins as you sew past them.

Make sure that the elastic or fabric ties are secured in the corners, sandwiched by your two layers of fabric, as you sew over their ends. You want to make sure your needle goes through the three pieces: the top layer, the end of the fabric tie, and the bottom layer. Add a couple stitches forward and backward (in both directions) to secure your ties in place.

Step 5: Stitch all around

Stitch all around the perimeter of the fabric layers, repeating the forward and backward motion at each corner to secure all the elastic ends or fabric ties.

Continue to stitch your way toward the starting point, but stop to allow for a 1-1/2 inch gap.

Step 6: Turn out

Turn your project right-side out from the little 1-1/2 inch gap. Your fabric ties or elastics should now stick out, like little legs.

Step 7: Pleats please

Make three staggered pleats lengthwise on the mask, as if folding a paper fan. This helps the mask conform to the wearer’s face. Secure each pleat with pins.

Step 8: Finishing up

With your pleats held in place by pins, stitch around the perimeter of the mask, 1/4-inch away from the edge of the seam. This is called a top stitch. Take care when stitching over the pleats as the fabric may be quite thick.

Top stitch a second time around, about 1/4 inch in from the first round of stitching. Now you have a completed mask.

Next up? Learning to wear a mask correctly is important. Many people pull them aside, hampering their effect, and also air can get in easily around the edges.

📣 The Indian Express is now on Telegram. Click here to join our channel (@indianexpress) and stay updated with the latest headlines

For all the latest Explained News, download Indian Express App.


0
Comment(s)

*
* The moderation of comments is automated and not cleared manually by indianexpress.com.
* The moderation of comments is automated and not cleared manually by indianexpress.com.

This content was originally published here.

Leave a Reply